Restaurant Hood System 8ft

Hood #1

1 – 4824EX-2-PSP-F – 8ft 0″ Long Exhaust-Only Wall Canopy Hood with Front Perforated Supply Plenum with Built-in 3″ Back Standoff

• 1 – 430 SS Where Exposed
• 1 – Fire Cabinet on the Right Side 12.00″ Width x 48.00″ Length x 24.00″ Height (Additional charges may apply for cabinet if not sold with fire      system)
• 2 – FILTER – 16″ tall x 16″ wide Kleen-Gard Stainless Steel Baffle Filter with Handles and Bottom Hanging Hook, UL Classified
• 2 – L55 Series E26 Canopy Light Fixture – High Temp Assembly, Includes Clear Thermal and Shock Resistant Globe (L55 Fixture), Bulbs By Others
• 1 – EXHAUST RISER – Factory installed 14″ Diameter X 4″ Height
• 1 – SUPPLY RISER – 12″x 24″ Supply Riser with Volume Dampers
• 1 – 1/2 Pint Grease Cup New Style, Flanged Slotted
• 1 – Parts required to mount prewire sensor in capture volume of hood. Sensor installed directly in line with center of riser and in center of capture volume front to back. Sensor supplied from ECP tied to hood.

Fire System #1 *FINAL HOOK UP, TESTS and PERMITS NOT INCLUDED*

1 – ANSUL-3.0 Ansul 3 gallon Fire System in Utility Cabinet (includes pre-piped hood(s) with detection, tank(s), release mechanism, microswitches and pull station).  Includes piping for hood: 1.

• 1 – MGVA2 GAS VALVE – 2″ Mechanical Shutoff Valve (Ansul)(28-55610) – Includes Upstream Strainer assembly

NOTE: All Necessary Ansul R-102 Parts To Be Provided (Price/ System Size May Change Based On Appliances)

EADU85H – Exhaust Fan (KEF-1)

1 – EADU85H High Speed Direct Drive Centrifugal Upblast Exhaust Fan with speed control (speed control included for single phase only), disconnect switch and 15-3/4″ wheel.  Exhaust Fan handles 2000 CFM @ -1.000″ wc ESP, Fan runs at 1402 RPM.  Exhaust Motor: 0.750 HP, 1 Phs, 115 V, 60Hz, 9.8 FLA, ODP (Open Drip Proof)

• 1 – Grease Cup for kitchen-duty centrifugal exhaust fans, Box Dimensions 17-1/8 L X 5-1/16 W X 3-3/4 H (18 GA.) (Includes Down Spout)
• 1 – KEF-1 Curb CRB23X20E On Fan #1 Flat Curb
• 1 – Hinged Base for Curb. Standard Hinge attached to curb. Used on Fans with wheels 20 inches or smaller. 12 GA Galvanized.
• 1 – Vented Base for Curb

EA-A1-G10 – Supply Fan (MUA-1)

1 – EA-A1-G10 Untempered Supply Unit with 10″ Blower in Size #1 Housing
Supply Fan handles 1600 CFM @ 0.500″ wc ESP, Fan runs at 749 RPM.
Supply Motor: 0.500 HP, 1 Phase, 115 V, 60Hz, 7.6 FLA, ODP (Open Drip Proof)
Down Discharge – Air Flow Right -> Left

• 1 – Sloped Filtered Intake for Size #1 Standard Untempered Supply Unit.
22″ Wide x 25.875″ Long x 23.375″ High.
Includes 2″ MV EZ Kleen Metal Mesh Filters.
• 1 – MUA-1 Curb CRB21X20 On Fan #2 Flat Curb

SC-111110FP Electrical Control Panel (Satisfies Automatic Activation Code) Adds: USD $730.00

***ETL Listed Grease Ductwork Is Available Upon Request***

***Stainless Steel Enclosure Panels/ Stainless Steel Wall Panels Are Available Upon Request***

FREE SHIPPING